We have uncovered this great article relating to How to Install a Bathtub below on the net and decided it made sense to share it with you here.
Mounting a bathtub isn't specifically rocket science, but it does require strong plumbing, carpentry, as well as occasionally, tiling abilities. Replacing an old tub with a new one is additionally a moderately hard project. If the old bathtub is readily accessible, the project can relocate quickly; if you have to open a wall to remove the old bathtub and also place the brand-new bath tub, the job is a lot harder. In either instance, the project is within a house handyman's skills, although you will require a helper to move out the old tub and also set in the brand-new one. Ensure you have actually qualified yourself for the job and are comfortable trying it. As opposed to working with a professional to take control of a halfway-completed task, it is better to take into consideration employing one prior to you begin. Possibilities are you might need an expert plumber to make tube connections.
This short article will aid you set up a new tub in your bathroom if you have already purchased a brand-new bathtub as well as don't need to alter the plan of your previous water supply pipelines.
Your tools and also material list must make up the following:
Preparing for the Installment
To start with, the supporting framework supplied with the bathroom should be fitted (if required) according to the producer's directions. Next off, fit the taps or mixer to the tub. When suitable the tap block, it is important to see to it that if the faucet features a plastic washing machine, it is fitted between the bathroom as well as the faucets. On a plastic bath, it is additionally practical to fit a sustaining plate under the taps unit to avoid pressure on the bath tub.
Fit the flexible tap adapters to the bottom of both taps utilizing 2 nuts and also olives (occasionally supplied with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet hole, and then pass the electrical outlet with the hole in the bathroom. Make use of the nut supplied by the supplier to fit the plug-hole. Examine the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next, fit the end of the flexible overflow pipe to the overflow outlet. After that, screw the pipe to the overflow face which need to be fitted inside the bath. Make sure you utilize all of the supplied washers.
Connect the trap to the bottom of the waste outlet on the tub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, as well as screw on the trap to the electrical outlet. Attach the bottom of the overflow tube in a similar manner.The bathroom must now prepare to be suited its final setting.
Removing Old Touches
If you need to change old faucets with new ones as a part of your installation, after that the first thing you ought to do is detach the supply of water. After doing so, switch on the faucets to drain pipes any kind of water staying in the system. The procedure of eliminating the existing taps can be rather bothersome due to the limited gain access to that is commonly the situation.
Utilize a container wrench (crowsfoot spanner) or a tap tool to undo the nut that connects the supply pipelines to the faucets. Have a cloth ready for the remaining water that will originate from the pipelines. When the supply pipelines have been gotten rid of, use the exact same device to loosen up the nut that holds the faucets onto the bath/basin. You will certainly need to stop the solitary faucets from transforming throughout this procedure. Once the faucets have been gotten rid of, the holes in the bath/basin will have to be cleansed of any kind of old securing compound.
Before carrying on to fit the new taps, contrast the pipeline connections on the old faucets to the new faucets. If the old faucets are longer than the new faucets, then a shank adapter is needed for the brand-new faucets to fit.
Installing the Bath tub
Making use of the two wooden boards under its feet, place the tub in the called for setting. The wooden boards are practical in evenly spreading the weight of the bathtub over the location of the boards instead of concentrating all the weight onto 4 tiny points.
The next objective is to guarantee that the bath tub is leveled all round. This can be accomplished by checking the spirit level and also adjusting the feet on the bath tub until the level reviews degree.
To install faucets, fit the bottom of the furthest adaptable tap connector to the suitable supply pipeline by making a compression sign up with; then do the same for the various other tap.
Activate the water supply and check all joints as well as new pipework for leaks and tighten them if necessary. Load the bath tub as well as also examine the overflow outlet and also the regular outlet for leakages.
Finally, fix the bath paneling as explained in the manufacturer's instruction manual. Tiling and securing around the tub should wait up until the bathtub has actually been used a minimum of once as this will certainly settle it right into its final setting.
Suitable New Taps
If the tails of the brand-new faucets are plastic, after that you will certainly require a plastic connector to avoid damages to the thread. One end of the port fits on the plastic tail of the faucet and also the other end offers a connection to the existing supply pipes.
If you require to fit a monobloc, then you will require reducing couplers, which links the 10mm pipeline of the monobloc to the basic 15mm supply pipe.
Next, position the faucet in the installing opening in the bath/basin guaranteeing that the washers are in area between the tap as well as the sink. Protect the tap in position with the supplier offered backnut. When the faucet is firmly in position, the supply pipes can be linked to the tails of the taps. The faucets can either be attached by utilizing corrugated copper piping or with typical tap ports. The previous type should be connected to the tap finishes first, tightening only by hand. The supply pipelines can later be connected to the various other end. Tighten both ends with a spanner after both ends have actually been linked.
Tiling Around the Tub
In the area where the bath satisfies the ceramic tile, it is needed to seal the accompanies a silicone rubber caulking. This is essential as the fitting can relocate enough to fracture a rigid seal, creating the water to penetrate the wall surface between the bath and the tiling, resulting in difficulties with dampness as well as feasible leakages to the ceiling below.
You can choose from a variety of coloured sealers to blend in your fixtures as well as installations. They are marketed in tubes and cartridges, as well as can sealing gaps as much as a width of 3mm (1/8 inch). If you have a bigger void to fill up, you can fill it with spins of soaked paper or soft rope. Remember to always fill up the tub with water prior to securing, to enable the activity experienced when the tub is in use. The sealant can crack fairly very early if you do not take into account this activity prior to securing.
Conversely, ceramic coving or quadrant floor tiles can be utilized to border the bathroom or shower tray. Plastic strips of coving, which are easy to use as well as reduce to dimension, are additionally quickly readily available on the market. It is advisable to fit the ceramic tiles making use of waterproof or water-proof glue as well as grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
I recently found that piece on A Step-by-Step Guide to Installing a Bathtub when perusing the search engines. Liked our write up? Please share it. Let someone else discover it. We thank you for reading our article about How to Install a Bathtub.
Emergency plumber? One call away.